Lanner FW-8892 Manual do Utilizador

FW-8892 Manual

FW-8892 10 Processor 1U CPU heat-sink Cooling System 4 x 4056 System Fan + 2 x 4028 System Fan (Support Smart FAN control.) Temperature, Ambient ope

FW-8892 11 1.5 Technical Assistance Should you have any questions or problems with your product, please contact the Lanner sales team. Phone: 886-2

FW-8892 12 2. System Components 2.1 MB-8892 system Board MB-8892 is the system board bundled with the FW-8892 Network security platform. The succee

FW-8892 13 Figure 3 – MB-8892 Bottom View

FW-8892 14 Figure 4 – MB-8892 Dimension

FW-8892 15 2.1.2 Jumper Settings and I/O Connectors The jumper settings and I/O connectors of the MB-8892 board are specific to the FW-8892. Changin

FW-8892 16 Jumper Settings and I/O Connector Summary for MB-8892： JUMPER FUNCTION LANB2 RJ45 connector for IPMI management (FW-8892C & FW-8892D o

FW-8892 17 2.1.3 Connectors Pin Assignment z Ethernet Interface Part reference: LANB2 Bellow shows the pin assignment of the RJ45 connector for E

FW-8892 18 z VGA Connector Part reference: J16 Bellow shows the pin assignment of the VGA connector PIN DESCRIPTION 1 RED 2 CRT

FW-8892 19 z POWER 24 Pin ATX Power Connector Part reference: ATXPWR2 PIN DESCRIPTION PIN DESCRIPTION 1 +3.3V 13 +3.3V 2 +3.3V 14 -12V 3 G

FW-8892 2 FW-8892 Manual Copyright 2009, Lanner Electronics, Inc. All rights reserved. This document contains proprietary information that

FW-8892 20 z OPMA connector Part reference: CON1 z PCIE Interface (x8) Part reference: PCIEC1 (x8); PCIEC2 (x8); PCIEC3 (x8) Lan Module Connector Pa

FW-8892 21 z LCM Part reference: J9 PIN DESCRIPTION PIN DESCRIPTION 1 P5V 13 FL_PD7 2 GND 14 FL_PD6 3 P_SLIN# 15 LCD- 4 VEE 16 P5V 5 P_AFD# 17

FW-8892 22 z PCIE Interface (x4) Æ Option Part reference: PCIE1 PIN DESCRIPTION PIN DESCRIPTION Side B Side A 1 +12v 1 PRSNT#1 2 +12v 2 +12v 3 R

FW-8892 23 2.2 Mechanical Overview This section of the manual describes the mechanical and device nomenclature of FW-8892. 2.2.1 Front View, L

FW-8892 24 LED Indicate on LAN Module Color Status Description ON When LAN is connecting. Yellow Blinking When data is accessing. 100M 10/100 G

FW-8892 25  RC-88922A supports two PCI-Ex4 expansion cards (one for external and the other for internal.) Warning: Faulty or improper use of the

FW-8892 26 3. Hardware Installation Guide 3.1 System Memory Position the DIMM module to the DIMM socket properly, so the notch on the memory module

FW-8892 27 rack should be such that a hazardous condition is not created due to uneven mechanical loading. 3. Circuit Overloading - Consideration sho

FW-8892 28 Installing the outer rails to the rack: Use the following procedures to install the outer rail: 1. Attach the rail to the posts of the

FW-8892 29 4. BIOS Setup BIOS Setup AMI’s ROM BIOS provides a built-in Setup program that allows users to modify the basic system configuration and se

FW-8892 3 Safety Guidelines Follow these guidelines to ensure general safety: z Keep the chassis area clear and dust-free during and after installati

FW-8892 30 4.1 Main Program Screen This screen provides access to the utility‘s various functions. Listed below is explanation of the keys displa

FW-8892 31 4.2 Main Menu When you select the “Main Menu” on the main program, the screen display will appears as: The Main Meun utility is used t

FW-8892 32 4.3 Advanced Menu When you select the “Advanced Menu” on the main program, the screen display will appear as: The following explains t

FW-8892 33 IDE Configuration: The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select

FW-8892 34 Configure SATA#1 as: Configuration options: [IDE] [AHCI] SATA#2 Configuration: This is for setting SATA#2 configuration. Configuration o

FW-8892 35 Primary IDE Master: Type: Selects the type of IDE drive. Setting to Auto allows automatic selection of the appropriate IDE device type.

FW-8892 36 Configuration options: [Auto] [DMA0][SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]. SMART Mo

FW-8892 37 Super IO Configuration: Press <Enter> to enter the sub-menu and the following screen appears: Serial Port1/2 Address: These items

FW-8892 38 Hardware Health Configuration: Press <Enter> to enter the sub-menu and the following screen appears: H/W Health-Temperature and FA

FW-8892 39 H/W Health-SMART FAN Control: These items allow you to select system fan control mode & set the Target Temperature Value. Configuratio

FW-8892 4 z Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available, ground yourself by touching

FW-8892 40 H/W Health Voltage: These items allows you to set 1.5V, 3.3V, 12V and 5V voltage

FW-8892 41 USB Configuration: Press <Enter> to enter the sub-menu and the following screen appears: USB Function: Allows you to enable or dis

FW-8892 42 USB Mass Storage Device Configuration: To set the number of seconds POST waits for the USB mass storage device after start unit command.

FW-8892 43 Remote Access Configuration: Press <Enter> to enter the sub-menu and enable Remote Access then the following screen appears: Seria

FW-8892 44 Restore on AC power loss by: Select Power Status. Configuration options: [Power Off] [Power On] [Last State]. Clock Gen Differential Ou

FW-8892 45 Power Off LAN bypass Press <Enter> to select the Power Off LAN bypass status: Configuration options: [Disable] [Enabled].

FW-8892 46 4.4 Boot Menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub

FW-8892 47 PS/2 Mouse Support: Allows you to enable or disable support for PS/2 mouse. Configuration options: [Disabled] [Enabled] [Auto]. Wait for ‘

FW-8892 48 4.5 Security Menu Press <Enter> to enter the sub-menu and the following screen appears: Type the password, up to 6 characters in

FW-8892 49 4.6 Exit Menu Press <Enter> to enter the sub-menu and the following screen appears: Save Changes and Exit: Once you are finished

FW-8892 5 EMC Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC R

FW-8892 50 Appendix A: Power Supply A.1 Power Supply Specifications Input specifications： Output specifications：

FW-8892 51 A.2 Feature • Total output is 500W and 80% efficiency • Temperature Range: Operating ranges from 0 to 40 , Storage ℃℃ranges from -20

FW-8892 52 Appendix B: Watchdog Timer B.1 Introduction Most systems need to be self-reliant. If an error should occur it is typically not possible t

FW-8892 53 Appendix C: Console Redirection Console redirection lets you maintain a system from a remote location by re-directing keyboard input and t

FW-8892 54 D. Appendix D: LCM Module and Keypad for FW-8892 D.1 Purpose of this chapter The purpose of this document is to provide installation info

FW-8892 55 E. Appendix E: LAN Bypass Function E.1 Introduction The bypass function is used to link (or short) two independent Ethernet ports when th

FW-8892 56 F. Appendix F: Hot Swap System FAN F.1 Independent Hot Swap System FAN Hot swap allows devices to be removed and inserted while the syste

FW-8892 57 Terms and Conditions Warranty Policy 1. All products are under warranty against defects in materials and workmanship for a period of on

FW-8892 58 RMA Service Request Form When requesting RMA service, please fill out the following form. Without this form enclosed, your RMA cannot be pr

FW-8892 6 ContentsSAFETY GUIDELINES...3 EMC NOTICE...

FW-8892 7 4.6 EXIT MENU ... 49 APPENDIX A: POWER SUPPLY...

FW-8892 8 1. Product Overview 1.1 Product Introduction Figure 1 － FW-8892 Outlook Built around the Intel 5520 chipset, the FW-8892 is the new ben

FW-8892 9 1.3 Specifications FEATURE DESCRIPTION Form Factor 19” 2U Rack-mount Processor z Supports up to two Intel Nehalem family processors (G